Paradyne 1740 SHDSL Manuel d'utilisateur

1740 SHDSL 2/4-Wire Router User’s Guide Document Number 1740-A2-GB20-00 July 2004

1740 SHDSL 2/4-Wire Router User’s Guide 2.2 Rear-panel Connections DSL connection Connect the supplied RJ45 cable to the port marked LINE at the back

1740 SHDSL 2/4-Wire Router User’s Guide CHAPTER 3 Quick Installation This section describes how to manage the router via the Web browser from the

1740 SHDSL 2/4-Wire Router User’s Guide STEP 5: After successfully logging in, you will reach the main configuration page. The left hand side has a me

1740 SHDSL 2/4-Wire Router User’s Guide 3.1.2 Web Page Layout On each Web page, there are two areas.  Menu Bar: On the left side of the Web page

1740 SHDSL 2/4-Wire Router User’s Guide 3.1.3 Monitoring the SHDSL Line Click Link Status on the Basic menu bar. The Link Status screen has two tabs

1740 SHDSL 2/4-Wire Router User’s Guide 3.2 WAN Interface Configuration The router supports 16 ATM interfaces. A virtual channel (VC) can be configur

1740 SHDSL 2/4-Wire Router User’s Guide 3.2.1 Bridge Mode: Service for One Fixed IP Address To configure one static IP address, you need to set up t

1740 SHDSL 2/4-Wire Router User’s Guide To modify the VC, click a VC from the Current ATM PVC List to display the parameters of the VC. Change its par

1740 SHDSL 2/4-Wire Router User’s Guide 3.2.2 Router Mode: Service for Five Static IP Addresses To set up the service for five static IP addresses

1740 SHDSL 2/4-Wire Router User’s Guide STEP 4: Click on the Add button. The new VC is added in the Current ATM PVC List on the bottom screen. To modi

1740 SHDSL 2/4-Wire Router User’s Guide Copyright © 2004 Paradyne Corporation. All rights reserved. Printed in U.S.A. Notice This publication is prote

1740 SHDSL 2/4-Wire Router User’s Guide After creating an RFC 1483 Routed VC, click LAN Setup to set up the router’s Ethernet IP address.  After ch

1740 SHDSL 2/4-Wire Router User’s Guide STEP2: select 0/34 from the Current ATM PVC List to display the parameters and click RFC 1483 Routed and then

1740 SHDSL 2/4-Wire Router User’s Guide STEP 4: Click Save & Reboot on the Basic menu bar to save your settings. 3.2.3 PPPoE When a VC is set i

1740 SHDSL 2/4-Wire Router User’s Guide Idle Timeout The Idle Time field defines the period of idle time after which the PPPoE link will be terminate

1740 SHDSL 2/4-Wire Router User’s Guide 3.2.4 PPPoA When a VC is configured for PPPoA, the router will auto-detect the Authentication code (PAP or CHA

1740 SHDSL 2/4-Wire Router User’s Guide To modify the VC, click a VC from the Current ATM PVC List to display the parameters of the VC. Change its par

1740 SHDSL 2/4-Wire Router User’s Guide 3.2.5 Password Setup There are two types of access privileges. A system ADMINISTRATOR is the only person that

1740 SHDSL 2/4-Wire Router User’s Guide 3.2.6 Setting the Bridge Click on Bridging on the Advanced menu bar to set up the static bridging and Spannin

1740 SHDSL 2/4-Wire Router User’s Guide 3.4 Static Bridging Click on the Static tab to configure, modify, and delete the static bridging functions.

1740 SHDSL 2/4-Wire Router User’s Guide 3.4.1 Write System Configurations The new parameters can function immediately without being saved to the flas

1740 SHDSL 2/4-Wire Router User’s Guide Preface This manual is designed to provide information to network administrators. It covers the installation,

1740 SHDSL 2/4-Wire Router User’s Guide 3.4.2 Load Factory Default Values Caution! If you reset your device to the factory defaults, any changes to p

1740 SHDSL 2/4-Wire Router User’s Guide CHAPTER 4 Setting up WAN and LAN Interfaces 4.1 LAN Interface To set up the Ethernet Interface: STEP 1: Cli

1740 SHDSL 2/4-Wire Router User’s Guide 4.2 Configuring the WAN Interface Click WAN Setup on the Basic menu bar and configure the VC to RFC 1483 Brid

1740 SHDSL 2/4-Wire Router User’s Guide 4.2.1 VC Data Flow Control To set up the flow control parameters, such as AAL5 encapsulation, QOS, Peak Cell

1740 SHDSL 2/4-Wire Router User’s Guide 4.2.2 Setting up an ISP The router supports connection to up to 16 ISPs. Each ATM Interface can connect to a

1740 SHDSL 2/4-Wire Router User’s Guide CHAPTER 5 SNMP The default setting of the SNMP function is enabled. SNMP is a software entity that responds

1740 SHDSL 2/4-Wire Router User’s Guide 5.2 Disable SNMP Click SNMP on the Advanced menu bar and click on the Modify button at the bottom of the scree

1740 SHDSL 2/4-Wire Router User’s Guide CHAPTER 6 Packet Filter Packet filter, a firewall security measure, examines incoming and outgoing packet he

1740 SHDSL 2/4-Wire Router User’s Guide Destination IP Destination IP of a packet you wish to filter. Destination Mask Destination Mask of a packet.

1740 SHDSL 2/4-Wire Router User’s Guide CHAPTER 7 Routing This chapter describes how to set up the static routes and RIP. Click Routing Setup from t

1740 SHDSL 2/4-Wire Router User’s Guide TTAABBLLEE OOFF CCOONNTTEENNTTSS CHAPTER 1 OVERVIEW ...

1740 SHDSL 2/4-Wire Router User’s Guide Delete: STEP 1: Select the entry you wish to delete from the List of Static Routes STEP 2: Change the paramet

1740 SHDSL 2/4-Wire Router User’s Guide Poison Reverse: Enabled: to enable the Poison Reverse Disabled: to enable the Splitting Horizon The default se

1740 SHDSL 2/4-Wire Router User’s Guide 7.3 Displaying the Routing Table To display the routing table, you can enter either of the following screens:

1740 SHDSL 2/4-Wire Router User’s Guide CHAPTER 8 NAT Network Address Translation (NAT or NAPT) is a transparent routing function that translates a

1740 SHDSL 2/4-Wire Router User’s Guide 8.1 Multiple to One This application requires a series of private IP addresses (such as 192.168.1.140- 192.16

1740 SHDSL 2/4-Wire Router User’s Guide 8.2 One to One NAT One-to-one NAT maps a private IP address to a public IP address, such as 192.168.1.10 to 1

1740 SHDSL 2/4-Wire Router User’s Guide 8.3 Multi-NAT Multi-NAT maps a set of continuous private IP addresses to a set of continuous public IP addres

1740 SHDSL 2/4-Wire Router User’s Guide Overload. When the number of private IP addresses is greater than the number of public IP addresses, private I

1740 SHDSL 2/4-Wire Router User’s Guide 8.4 Virtual Server If you want to set up Internet servers (such as an e-mail server, web server, or FTP serve

1740 SHDSL 2/4-Wire Router User’s Guide CHAPTER 9 DHCP The router can be set as a Dynamic Host Configuration Protocol (DHCP) server or a DHCP relay.

1740 SHDSL 2/4-Wire Router User’s Guide 5.2 Disable SNMP...

1740 SHDSL 2/4-Wire Router User’s Guide 9.2 DHCP Relay Click on DHCP on the Advanced menu bar. On the main screen, click on the BOOTP/DHCP Relay tab a

1740 SHDSL 2/4-Wire Router User’s Guide CHAPTER 10 DNS Proxy A Domain Name Server (DNS) provides an IP address to a host computer for an applied Dom

1740 SHDSL 2/4-Wire Router User’s Guide CHAPTER 11 IGMP IGMP (Internet Group Membership Protocol) is a protocol used by IP hosts to report their mu

1740 SHDSL 2/4-Wire Router User’s Guide STEP 4: Click Apply to submit the settings. 1740-A2-GB20-00

1740 SHDSL 2/4-Wire Router User’s Guide CHAPTER 12 VLAN To configure the VLAN function, click on VLAN in the Advanced menu bar. VLAN is disabled by

1740 SHDSL 2/4-Wire Router User’s Guide CHAPTER 13 Maintenance and Diagnostics This chapter describes how to perform a software upgrade, configurati

1740 SHDSL 2/4-Wire Router User’s Guide If a wrong format of the file us uploaded, a failure message will display during the upgrade. The following is

1740 SHDSL 2/4-Wire Router User’s Guide The following is an example of how to set up the parameters for homepage upgrade. To upload the configurati

1740 SHDSL 2/4-Wire Router User’s Guide 13.2 OAM Loopback Click on Utilities on the Advanced menu bar, and click on the Loopback tab on the main scre

1740 SHDSL 2/4-Wire Router User’s Guide 13.3 Ping A Ping test is used to verify the status of a network connection after the RIP or static route funct

1740 SHDSL 2/4-Wire Router User’s Guide 16.1.4 Password Setup ...

1740 SHDSL 2/4-Wire Router User’s Guide 13.4 Performance Monitoring  System statistics Click System Statistics on the Advanced menu bar to monitor

1740 SHDSL 2/4-Wire Router User’s Guide To display the interface statistics, click on the Interface tab, located at the top-left of the System Statist

1740 SHDSL 2/4-Wire Router User’s Guide To view TCP-IP statistics click on the TCP-IP tab at the top of the System Statistics page. The TCP-IP page d

1740 SHDSL 2/4-Wire Router User’s Guide CHAPTER 14 Application Example 14.1 Adding the Static Route (Web) Click Routing Setup on the Advanced menu

1740 SHDSL 2/4-Wire Router User’s Guide Enter the parameters of the static route and click on the Add button. Click LAN Setup on the Basic men bar.

1740 SHDSL 2/4-Wire Router User’s Guide CHAPTER 15 Pin Assignments Console Port (RS232 DB9) Pin number Definition Pin number Definition 1 NC 6 N

1740 SHDSL 2/4-Wire Router User’s Guide CHAPTER 16 Console Access To access the device via the console port the following are required:  VT100 Com

1740 SHDSL 2/4-Wire Router User’s Guide 16.1.2 Keyboard Operations In this table, the caret (^) denotes the Ctrl key. ↑ The upward arrow key mov

1740 SHDSL 2/4-Wire Router User’s Guide The backup keys displayed at the bottom of the screen. In addition to the arrow keys to move the cursor in t

1740 SHDSL 2/4-Wire Router User’s Guide STEP 3: Press the 2 key, and then press the Enter key in MAIN/ADVANCE/DHCP. STEP 4: Now you have reached MAI

1740 SHDSL 2/4-Wire Router User’s Guide CHAPTER 1 Overview The 1740 SHDSL router satisfies the needs of multiple users in small/home offices and rem

1740 SHDSL 2/4-Wire Router User’s Guide 16.1.4 Password Setup Enter MAIN/BASIC/SYSTEM to change the passwords.  New Administrator Password and Rety

1740 SHDSL 2/4-Wire Router User’s Guide 16.1.7 Save the Configurations The new parameters can function immediately without being saved to the flash m

1740 SHDSL 2/4-Wire Router User’s Guide STEP 2: Click [Start]> [run], type telnet 192.168.1.1 and click OK. (192.168.1.1 is the default IP address.

1740 SHDSL 2/4-Wire Router User’s Guide Appendix A: Specifications WAN Interface (One SHDSL port) SHDSL standard ITU-T G991.2 SHDS

1740 SHDSL 2/4-Wire Router User’s Guide 74 July 2004

1740 SHDSL 2/4-Wire Router User’s Guide 1.2 LED Indicators There are eight LEDs on the front panel of the router; the functions of the LEDs are descri

1740 SHDSL 2/4-Wire Router User’s Guide CHAPTER 2 Installation 2.1 Preparing for Hardware Installation The following equipment may be necessary to