Paradyne 24-Port Manuel d'utilisateur

1SMD2000-24T 24-Port SHDSL Mini DSLAMInstallation InstructionsDocument Number SMD2-A2-GN11-00July 2005ContentsSoftware and Firmware License Agreement

10The two terminal blocks on the SMD2000-24T are independent feeds. Chassis power is supplied by only one terminal block at a time; the second supply

117. Verify the connection. Turn your power source ON. The PWR (power) LED on your SMD2000-24T faceplate will illuminate solid green to indicate that

123. Slide the RJ21 plug connector of your SHDSL cable underneath the hook-and-loop fastener from the right and press it firmly into the RJ21 socket o

13The speed and data passing capability of multiple SHDSL lines, as used for one network connection, is cumulative. For example, loop bonding three SH

14Connecting the Uplink LinesTo connect the SMD2000-24T to T1 service:1. Configure the T1 uplinks.No configuration is necessary for the SMD2000-24T to

15Default SettingsSHDSL Parameter DefaultsT1 Uplink Parameter DefaultsTable 1. SHDSL DefaultsParameter DefaultBackbone-VLAN 0 (off)Circuit Identificat

16System and Management DefaultsNo configuration is necessary for an SMD2000-24T to operate at default settings.User Access DefaultsTable 3. System an

17Data StorageConfiguration backup is inherent in the SMD2000-24T. Default parameters remain in place unless changed using the CLI, web management sys

18SMD2000-24T TemplateAn SMD2000-24T template file records all management and port configurations except IP Address.SHDSL Port TemplateA SHDSL port co

19Reset ButtonThe reset button is a small, unmarked button just to the right of the T1 uplink LEDs on the chassis faceplate. The button is recessed an

2Software and Firmware License Agreement The terms and conditions of this License Agreement (the “Agreement”) will apply to the software and/or firmwa

20Command Line Interface for 4000E and 12000E BACs, Micro DSLAMs, and Network Extenders User's Guide (Document Number CLI-A2-GB20) or the Network

21LNK (10/100 Ethernet Manage-ment Link)Flashing green100 Mbps management connection is established and activeTraffic is flowing at 100 Mbps.Solid gre

22AL: T1 Alarm Port 1 and 2No illuminationT1 uplink connection is operationalAn established T1 uplink connection has no alarm indications and is opera

23Pin AssignmentsSHDSL RJ21 Pinouts Pins 25 and 50 are not used.Table 10. SHDSL RJ21 PinoutsPortConnector Pins (Ring, Tip) PortConnector Pins (Ring,

2410/100BaseT RJ45 Pinouts T1 RJ48C Pin Assignments Table 11. Ethernet RJ45 ConnectionPin Connection1Rx+2Rx–3Tx+4 not used5 not u

25DB9 to 8-Pin Modular Adapter PinoutsTo connect the COM port to the DB9 serial port of a PC, use an adapter wired as shown: Pins not shown are unuse

26Technical SpecificationsTable 14. SMD2000-24T Technical SpecificationsSpecification CriteriaBandwidth and Distance Capabilities – SHDSL PortsDefault

27EMI NoticesUnited States – EMI NoticeThis equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Pa

28A plug and jack used to connect this equipment to the premises wiring and telephone network must comply with the applicable FCC Part 68 rules and re

29Japan NoticeClass A ITEThis is a Class A product based on the standard of the Voluntary Control Council for interference by Information Technology E

3b. ANY AND ALL IMPLIED WARRANTIES, INCLUDING WITHOUT LIMITATION IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NON-INFRI

30Important Safety Instructions1. Read and follow all warning notices and instructions marked on the product or included in the manual.2. Slots and op

31Warranty, Sales, Service, and Training InformationContact your local sales representative, service representative, or distributor directly for any h

32*SMD2-A2-GN11-00**SMD2-A2-GN11-00*

4Unpacking and Inspecting the EquipmentHANDLING PRECAUTIONS FOR STATIC-SENSITIVE DEVICESThis product is designed to protect sensitive components from

5Installing Uplink Interface Modules (Optional)An SMD2000-24T does not require installation of an Uplink Interface Module (UIM) for operational purpos

62.Mount the UIM on the SMD2000-24T Printed Circuit Board (PCB). A UIM may be installed in either Port 1 or Port 2, or both for redundancy purposes. U

75. Secure the faceplate. Using a Phillips screwdriver, secure the UIM faceplate to the SMD2000-24T faceplate with the two flathead screws included in

8Rack InstallationProcedureTo install the SMD2000-24T in a rack:1. Using a Phillips screwdriver, attach the two provided rack mount brackets to the si

9Powering Up the SMD2000-24TCAUTION:Turn your DC power source off until you have completed connection of the SMD2000-24T as described below.Do not ope